Fuse Holders

Works on Cars, boats, RV's and more (DC current 12/24/32V)
AGU Fuse Holder upto 100A
Water Proof
Gold plated contacts
Fits upto a 8 Gauge Wire (6mm max)

Works on Cars, boats, RV's and more (DC current 12/24/32V)
AFS Fuse Holder upto 100A
Water Proof
Gold plated contacs
Dimensions: Length 82mm (3.2") X Width 25mm (1") X Height 31mm (1.2")
Fits upto a 4 Gauge Wire (8mm max)

Works on Cars, boats, RV's and more (DC current 12/24/32V)
Removable Waterproof cap to protect fuse
16AWG Copper Wire with 105C rated insulation
Use for Upto 15A @ 12V depending on your setup

Works on Cars, boats, RV's and more (DC current 12/24/32V)
Removable Waterproof cap to protect fuse
10AWG Braided Copper Wire
Use for upto 40A @ 12V depending on your setup

Use one Power wire to have two separate protected circuits using this Twin AGU Fuse holder
Works on Cars, boats, RV's and more (DC current 12/24/32V)
Twin AGU Fuse Holder upto 100A for each
Gold plated contacts
Input Power side 1X 8.5mm hole (4AWG)
Output power side 2X separate 5.5mm hole (8AWG)
Dimensions: 100mm X 45mm X 30mm (4" X 1.8" X 1.2")
Weight: 150g (5.2oz)

Use one Power wire to have three separate protected circuits using this Triple AGU Fuse holder
Works on Cars, boats, RV's and more (DC current 12/24/32V)
Triple AGU Fuse Holder upto 100A for each
Gold plated contacts
Input Power side 3X 8.5mm hole (4AWG)
Output power side 3X separate 5.5mm hole (8AWG)
Dimensions: 100mm X 60mm X 30mm (4" X 2.4" X 1.2")
Weight: 228g (8.1oz)

Use one Power wire to have four  separate protected circuits using this Quad AGU Fuse holder
Works on Cars, boats, RV's and more (DC current 12/24/32V)
Quad AGU Fuse Holder upto 100A for each
Gold plated contacts
Input Power side 3X 8.5mm hole (4AWG)
Output power side 4X separate 5.5mm hole (8AWG)
Dimensions: 100mm X 78mm X 30mm (4" X 3" X 1.2")
Weight: 304g (10.7oz)

Works on Cars, boats, RV's and more (DC current 12/24/32V)
AFS Fuse Holder upto 100A
Gold plated contacts
Fits upto a 4 Gauge Wire (8mm max)
Dimensions: Length 52mm (2") X Width 36mm (1.4") X Height 28mm (1.1")

Use one Power wire to have two separate protected circuits using this Twin AFS Fuse holder
Works on Cars, boats, RV's and more (DC current 12/24/32V)
Twin AFS Fuse Holder upto 100A
Gold plated contact
Input Power side 1X hole up to 4GA (8mm max)
Output power side 2X separate hole up to 4GA (8mm max)
Dimensions: 67mm X 52mm X 29mm (2.6" X 2" X 1.1")

Works on Cars, boats, RV's and more (DC current 12/24/32V)
ANL Fuse Holder upto 300A
Gold plated contact.
Fits upto a 1/0 Gauge Wire (13mm max both sides)
Dimensions: Length 105mm (4.1") X Width 53mm (2") X Height 39mm (1.5")

Use one Power wire to have two separate protected circuits using this Twin ANL Fuse holder
Works on Cars, boats, RV's and more (DC current 12/24/32V)
ANL Fuse Holder upto 300A
Gold plated contacts
Input Power side 1X hole up to 1/0GA (13mm max)
Output power side 2X separate hole up to 4GA (8mm max)
Dimensions: Length 137mm (5.3") X Width 61mm (2.4") X Height 40mm (1.5")

Works on Cars, boats, RV's and more (DC current 12/24/32V)
Removable Clear cap to protect fuse
Rubber boots to protect wire at each exit
Will fit upto a 9.5mm diameter wire (approx 4ga)

Works on Cars, boats, RV's and more (DC current 12/24/32V)
Removable Waterproof cap to protect fuse
8AWG Wire with 105C rated insulation (6 Inch of wire on each side)
Use for upto 70A @ 12V depending on your setup
Dimensions of holder (black part) Length 80mm (3.1") X Width 18mm (0.7") X Height 55mm (2.1")

Works on Cars, boats, RV's and more (DC current 12/24/32V) using the mini blade fuses design to allow you to add a new fuse protected circuit into an existing circuit. Great for adding in LCD's and other devices that you need to be protected and/or powered on with the ignition key.
Pre clamped ready to clamp onto your new circuits power wire
16AWG Wire with 105C rated insulation
Use for Upto 10A for the new fuse circuit depending on your setup

Note: This is for low profile mini blade fuse setups
Works on Cars, boats, RV's and more (DC current 12/24/32V) using the mini blade fuses design to allow you to add a new fuse protected circuit into an existing circuit. Great for adding in LCD's and other devices that you need to be protected and/or powered on with the ignition key.
Pre clamped ready to clamp onto your new circuits power wire
16AWG Wire with 105C rated insulation
Use for Upto 10A for the new fuse circuit depending on your setup